본문 바로가기
잡다

로터리 스위치 납땜

by Oh.mogilalia 2019. 8. 19.

The rotary switch will be used to toggle between the output voltages. It can monitor one output voltage at a time are soldered four wires to it. Orange, red, yellow and purple. The voltmeter will be powered by a 5 volt wire and it's yellow sensor wire will be soldered to the central connector of the switch to easily make the ground connections. I'll cut four black wires and solder them to a 2.5 millimeter wire.
로터리 스위치는 출력 전압 사이를 전환하는 데 사용됩니다.  한 번에 하나의 출력 전압을 모니터링 할 수 있으며 4 개의 전선이 납땜됩니다.  주황색, 빨간색, 노란색 및 자주색.  전압계는 5 볼트 와이어로 전원이 공급되며 노란색 센서 와이어는 스위치의 중앙 커넥터에 납땜되어 접지 연결을 쉽게합니다.  4 개의 검은 색 와이어를 잘라 2.5mm 와이어에 납땜합니다.
Shrinking tube. I'll prepare three red wires and 3 yellow wires for the other outputs. We can cut the excess plastic from the voltmeter. We keep one black wire for the green switch and cut all the other wires that we don't need.
수축 튜브.  다른 출력을 위해 3 개의 빨간색 선과 3 개의 노란색 선을 준비하겠습니다.  전압계에서 여분의 플라스틱을 자를 수 있습니다.  녹색 스위치를 위해 검은 색 와이어 하나를 유지하고 필요하지 않은 다른 와이어는 모두 자릅니다.
Next The Binding posts. The black binding posts are too close to the circuit board and wires. I need to shorten them like this. I'll prepare a 2.5 millimeter black wire to connect the three ground binding posts.
다음 바인딩 포스트.  검은 색 바인딩 포스트가 회로 보드 및 와이어에 너무 가까이 있습니다.  이렇게 짧게해야합니다.  3 개의 접지 바인딩 포스트를 연결하기 위해 2.5mm 블랙 와이어를 준비하겠습니다.
Shrinking tubes cannot be inserted here. The Binding post will be insulated with electrical tape. I'll use the shrinking tube at the end to prevent the tape from peeling off. The positive 3.3 volts binding post needs to be shortened as well. I'll use hot glue for the LED and USB port after that. I'll solder their ground wires to the thick black one.
수축 튜브는 여기에 삽입 할 수 없습니다.  바인딩 포스트는 전기 테이프로 절연됩니다.  테이프가 벗겨지지 않도록 끝에 수축 튜브를 사용하겠습니다.  양의 3.3 볼트 바인딩 포스트도 짧아 져야합니다.  그 후 LED 및 USB 포트에 핫 접착제를 사용합니다.  접지선을 두꺼운 검은 색으로 납땜합니다.
And now we connect everything. Hopefully they'll all fit together.

Solder the green wire and the black wire to the green switch now Soldier the red switch wires to the AC input for the ammeter. I prefer to solder the wires instead of using the connector because I don't want to lose any power from an imperfect connection. The ground wire will go through the ammeter. So it will measure the total amount of current use from all the outputs the what meter in rockers which are a bit loose. So I'll stick them to the panel with hot glue.
이제 우리는 모든 것을 연결합니다.  잘만되면 그들은 모두 함께 맞을 것이다.

 녹색 와이어와 검은 색 와이어를 녹색 스위치에 납땜하십시오. 빨간색 스위치 와이어는 전류계의 AC 입력에 연결하십시오.  불완전한 연결로 인한 전력 손실을 원하지 않기 때문에 커넥터를 사용하는 대신 전선을 납땜하는 것을 선호합니다.  접지선은 전류계를 통과합니다.  따라서 모든 출력에서 ​​로커의 미터가 약간 느슨한 전류의 총 사용량을 측정합니다.  뜨거운 접착제로 패널에 붙입니다.

'잡다' 카테고리의 다른 글

알리 우체국 송장  (0) 2019.08.19
컴파워 DIY  (0) 2019.08.19
사전 선 정리하기  (0) 2019.08.19
전압전류계 연결  (0) 2019.08.18
바나나 플러그 숫놈 도착  (0) 2019.08.14